Msd 6al 2 Step Module

Be the first to write a review. This helps keep tire temperatures consistent.

Desoto Blower Manifold 276 291 Hemi Accepts 4 71 And 6 71 As Well As Our 8 71 Front Offset Blowers From The Blower Shop Desoto Hemi Supercharger

The Digital 2-Step Control is designed specifically for the MSD Digital 6AL Ignition.

Msd 6al 2 step module. 1 - Parts Bag Wiring Terminals 1 - Module Selector 4 - Mounting Screws Note. It is a multi-spark capacitive discharge electronic ignition designed for high performance street drag racing oval track and marine applications. The MSD Module Selectors allow you to choose two or three different rpm limits that can be activated at different times.

It provides the ability to set an rpm limit to be used during the launch of the vehicle through a switch or tied into a line-lock device or trans-brake. This install being done is on a 1988 Chevy Camaro IROC-Z. The Ignition will deliver full voltage with a supply of 9 - 18 volts and will operate with a supply voltage as low as seven volts.

Find MSD Ignition 8739 MSD Two Step Module Selectors and get Free Shipping on Orders Over 99 at Summit Racing. MSD Module Selectors Two Step PN 8739 Three Step PN 8737 Parts Included. 40 out of 5.

The MSD can be used with 16 volt batteries and can withstand a momentary 24 volts in case of jump starts. So I called up MSDs technical support and talked to a tech that knows the 6al-2 programmable very well. With a Three Step Module Selector plugged into the rpm socket of a 7AL-2 Ignition.

There is a Blue wire coming out of the 2-Step that controls when the launch. For example you can use a lower-rpm module for staging and then automatically switch to a higher-rpm module after you release your trans-brake or line lock. There is a Blue wire coming out of the 2-Step that controls when the launch.

MSD Two Step Launch Control InstallMSD 8733 for GM LS engines. Msd Two Step Wiring Diagram wiring diagram is a simplified usual pictorial representation of an electrical circuitIt shows the components of the circuit as simplified shapes and the talent and signal friends amongst the devices. By connecting one wire to the line-lock circuit one module will be activated during the burnout.

Page 2 INSTALLATION INSTRUCTIONS REV LIMITER STEP MODULE SELECTOR PN 8739 BLACK AUTOTRONIC CONTROLS CORPORATION 1490 HENRY BRENNAN DR EL PASO TX 79936 MODULE 2 MODULE 1. These MSD 2-step module selectors let you choose from two different rpm limits that can be activated at different times. MSD 6421 6AL-2 Ignition Control with 2-Step Rev Limiter.

MSD Ignition 8731 Digital 2-Step Rev Control for Ford 50L Engine. For example you can use a lower-rpm module for staging and then automatically switch to a higher-rpm module after you release your trans-brake or line lock. The MSD Module Selectors allow you to choose two different rpm limits that can be activated at different times.

These MSD 2-step module selectors let you choose from two different rpm limits that can be activated at different times. 1 - Module Selector 4 - Mounting Screws Note. The Procomp PC6AL-2 is the most powerful cd ignition of its type available.

1 - Parts Bag Wiring Terminals The MSD Module Selectors provide the ability to switch between two or three different rpm or degree modules. 10800 Suggested Retail 9660 Your Price Estimated shipping date. MSD 8739 Two-Step Module Selector.

Two Step Module Selector. I asked him if it would work if I set the box up without a timing map and wired it up for an ecu control let the ecu control timing and just set a 2 step limiter in it since theres a dedicated wire for the 2 step that has to see voltage to activate with the msd box. Do NOT use solid core spark plug wires with any MSD component.

Do NOT use solid core spark plug wires with any MSD component. With this ability the possibilities are endless. Switch between two different RPM or retard modules when used with one of the MSD Soft Touch Rev Controls or one of the MSD Timing Computers.

MSD 87331 2-Step Launch Control for Gen. The Digital 2-Step Control is designed specifically for the MSD Digital 6AL Ignition Control PN 6425. Requires the use of rpm modules sold separately.

MSD Ignition 6425 6AL Ignition Control Box. Two-Step Module Selector does not include RPM. As an example well use a drag car with a Three Step Module Selector plugged into the rpm socket of a 7AL-2 Ignition.

Page 1 MSD Module Selectors Two Step PN 8739 Three Step PN 8737 Parts Included. The PC6AL-2 uses the latest state of the art digital technology and when used with the Procomp high performance coil produces a spark gap current three times greater. With this ability the possibilities are endless.

Add to Cart Add to Cart Add to Cart Add to Cart. 50 out of 5 stars 2. The different rpm modules are activated when 12 volts are applied to a corresponding wire.

It provides the ability to set an rpm limit to be used during the launch of the vehicle through a switch or tied into a line-lock device or trans-brake. 50 out of 5 stars 3. MSD 6421 6AL-2 Ignition Control with 2-Step Rev Limiter.

This two step module is an add on for the MSD Digital 6AL and its purpose is to stop the 6AL from delivering spark to the engine holding it at a specified RPMThe two-step component is used to hold the engine at a lower rpm to control wheel spin and grip to achieve a shorter launch time. When the line-lock button is released. 50 out of 5 stars 2.

Im using a msd 6al box with a timing controlif i buy a 2step the 2 step plugs into the rev limiter module slot put the low rpm chip in one side of the 2step and put the module that i took out of the 6al box on the high sideis this correctcorrect me if im wrong please. As an example lets use a drag car. The different rpm modules are activated when 12 volts is applied to a corresponding wire.

An MSD 6AL-2 Ignition Control will operate on any negative ground 12 volt electrical system with a distributor.

Msd Adjustable 3 Step Launch Control Module Suits Msd Ignitions Msd8737 Msd Ignition